|
|
|
| Oscilloscopes |
|
Page 12 |
 |
MODEL S-1325 25MHz FEATURES • 2 Channel • DC:DC to 25MHz (within -3dB) • Weight 16.7 lbs. S-1325 ....................................$349.95 Specifications HERE |
|
|
|
 |
MODEL S-1345 40MHz FEATURES • 2 Channel • DC:DC to 40MHz (within -3dB) • Delay Sweep (.1ms to .25/div) • Beam Find • Component Tester • Z-Modulation - Y (CHB) Output • Acceleration Potential: Approx. 10KV • Weight 17.2 lbs. S-1345 ....................................$545.95 Specifications HERE |
|
|
|
 |
MODEL S-1340 40MHz FEATURES • 2 Channel • DC:DC to 40MHz (within - 3dB) • Acceleration Potential: Approx. 10KV • Weight 17.2 lbs. S-1340....................................$449.95 Specifications HERE |
|
|
|
 |
MODEL S-1360 60MHz FEATURES • 2 Channel • DC:DC to 60MHz (within -3dB) • Delay Sweep (.1ms to .25/div) • Beam Find • Component Tester • Z-Modulation - Y (CHB) Output • Acceleration Potential: Approx. 12KV • Weight 17.2 lbs. S-1360 .................................... $799.95 Specifications HERE |
|
|
|
 |
MODEL S-1330 25MHz FEATURES • 2 Channel • DC:DC to 25MHz (within -3dB) • Delay Sweep (.1ms to .25/div) • Beam Find • Component Tester • Z-Modulation - Y (CHB) Output • Acceleration Potential: Approx. 2KV • Weight 16.7 lbs. S-1330 ....................................$449.95 Specifications HERE |
| |
|
| SPECIFICATIONS COMMON TO ALL | |
| VERTICAL AXIS Sensitivity 5mV — 5 V/div ± 3% 10 steps selectable in 1-2-5 sequence with variable ctl Magnification 5 times 1 mV/div — (at x5 MAG) Bandwidth AC: 10 MHz — 40 MHz (within -3 dB) Rise time 9 ns or less (18ns – S1330, S1325) Overshoot 5% or less Input impedance 1 M W shunted by 25 pF ± 10 pF Maximum input voltage 400 (DC + AC peak) Operation mode CH1, CH2, DUAL (ALT or CHOP) and ADD Chop Frequency Approx. 500 kHx Polarity selection Possible only in CH2 HORIZONTAL AXIS Sweep time (nominal) 0.1 ms — 0.2 s/div ± 3% 20 steps selectable in 1-2-5 sequence Sweep Time (delay) 0.1 ms to .25/div 20 steps selectable in 1-2-5 sequence Magnification x10 to 10ns/div Linearity 3% or less Accuracy ±3% Hold off time Variable up to 5 times TRIGGER Trigger signal source CH1, CH2), ALT, LINE, EXT Trigger sensitivity auto 100Hz-60MHz 1.5V div (INT) .1V p-p (EXT) (norm) DC-60Hz-1KHz: .5 div (INT); .1V p-p (EXT) (TV-V) 20Hz-1KHz: .5 div (int); .05V p-p (EXT) (TV-H) 1KHz-100KHz: .5 div (int); .05V p-p (EXT) Coupling Auto, Norm, TV-V, TV-H X-Y OPERATION Sensitivity X-axis: Same as CH2, Y-axis: Same as CH1 X-axis bandwidth DC to 2 MHz (at -3 dB) Phase Shift Less than 3"at DC to approx 100KHz GENERAL Calibration Signal 2 Vp-p ± 3%; 1KHz Square wave CRT 6 inch screen with lighted internal graticule P31 phosphor; 8x10 divisions Power Requirements 90-137VAC or 198-264VAC 50/60Hz, 40W consumption Dimensions 12.8"W x 5.2"H x 15.6"D Standard accessories Operation manual, powercord, spare fuse 2 switchable 1x, 10x probes |
|
| OSCILLOSCOPE PROBES | |
 |
65MHz SCOPE PROBE Built in 3 position switch: X1, Ref, X10. 10 Meg ohms input impedance. Fits all scopes with BNC connector OP-1 ............................. $19.95 |
 |
100MHz SCOPE PROBE Built in 3 position switch: X1, Ref, X10. Complete with 5 accessories. 10 Meg ohms input impedance. Fits all scopes with BNC connector. OP-2 ............................. $24.95 |